U-Boot 2009.08-cm-fx6-0.85+tools (Aug 08 2013 - 10:11:21)

CPU: Freescale i.MX6 family TO6.4 at 792 MHz
Temperature:   27 C, calibration data 0x5c854169
mx6q pll1: 792MHz
mx6q pll2: 528MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock     : 66000000Hz
ipg per clock : 66000000Hz
uart clock    : 80000000Hz
cspi clock    : 60000000Hz
ahb clock     : 132000000Hz
axi clock   : 264000000Hz
emi_slow clock: 29333333Hz
ddr clock     : 528000000Hz
usdhc1 clock  : 198000000Hz
usdhc2 clock  : 198000000Hz
usdhc3 clock  : 198000000Hz
usdhc4 clock  : 198000000Hz
nfc clock     : 11000000Hz
Board: CM-FX6:[ POR ]
Boot Device: SPI NOR
I2C:   ready
RAM Configuration:
Bank #0: 10000000  1 GB
Bank #1: 80000000  1 GB
NAND:  No NAND device found!!!
0 MiB
MMC:   FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2
JEDEC ID: 0xbf:0x25:0x41
Reading SPI NOR flash 0xc0000 [0x2000 bytes] -> ram 0x17e01db8
SUCCESS

In:    serial
Out:   serial
Err:   serial
Net:   got MAC address from IIM: 00:00:00:00:00:00
FEC0
Hit any key to stop autoboot:  0 
CM-FX6 # printenv
baudrate=115200
console=ttymxc3,115200
bootscr=boot.scr
video_hdmi=mxcfb0:dev=hdmi,1920x1080M-24@50,if=RGB24
video_dvi=mxcfb0:dev=dvi,1280x800M-24@50,if=RGB24
mmcdev=2
mmcroot=/dev/mmcblk0p2 rw rootwait
nandroot=/dev/mtdblock4 rw
nandrootfstype=ubifs
mmcargs=setenv bootargs console=${console} root=${mmcroot} ${video}
nandargs=setenv bootargs console=${console} root=${nandroot} rootfstype=${nandrootfstype} ${video}
loadbootscript=fatload mmc ${mmcdev} ${loadaddr} ${bootscr}
bootscript=echo Running bootscript from mmc ...; source ${loadaddr}
loadkernel=fatload mmc ${mmcdev} ${loadaddr} ${kernel}
mmcboot=echo Booting from mmc ...; run mmcargs; bootm ${loadaddr}
nandboot=echo Booting from nand ...; run nandargs; nand read ${loadaddr} 0 400000 && bootm ${loadaddr}
run_eboot=echo Starting EBOOT ...; mmc dev ${mmcdev} && mmc rescan && mmc read 10042000 a 400 && go 10042000
serial=UTL-C1200QM-D2G-ND64-E2-LD-WB
ethact=FEC0
kernel=uImage-cm-fx6
video=video=mxcfb0:dev=hdmi,1920x1080M-24@50,if=RGB24
bootargs=setenv bootargs ${bootargs} ip=dhcp root=/dev/mmcblk0p2 rootwait elevator=noop ${video}
bootdelay=3
autoload=no
loadaddr=0x10800000
satadev=0
loadkernel_sata=fatload sata ${satadev} ${loadaddr} ${kernel}
sataroot=/dev/sda2 rootfstype=ext4 rw rootwait
sataargs=setenv bootargs console=${console} root=${sataroot} ${video}
sata_init=mw.l 0x20E0034 0x593A046
sataboot=echo Booting from sata ...; run sataargs; bootm ${loadaddr}
bootcmd_sata=run sata_init; sata dev ${satadev}; run loadkernel_sata; run sataboot;
bootcmd=run bootcmd_sata
ethaddr=00:01:c0:13:57:ed
stdin=serial
stdout=serial
stderr=serial

Environment size: 1613/8188 bytes
CM-FX6 #